Rough idle, hesitation, hard starting or poor fuel economy on a 2011–2017 Dodge Challenger with the 3.6L Pentastar V6 can lead to fuel-injector testing. Relevant fault codes include P0201–P0206 for injector circuits, P0300 for multiple-cylinder misfires and P0301–P0306 for individual-cylinder misfires. None proves that an injector needs replacement. Diagnose the circuit, ignition and mechanical condition before ordering parts. [2]
This guide covers replacement planning for the listed 2011–2017 Challenger 3.6L application. The detailed service references below are for a 2014 Challenger SXT 3.6L; their torque values are not presented as universal specifications for every year or every Pentastar vehicle. Obtain the factory procedure and diagrams for the exact car before opening its fuel system.
Skill level
Intermediate to advanced DIY; gasoline-system experience required.
Time allowance
Allow 3–5 hours after diagnosis; a planning allowance, not factory labor time.
Featured package
Six port-fuel injectors. Confirm seals, retainers and intake gaskets separately.
Check fitment · Diagnose the fault · Tools and supplies · DIY versus shop cost · Replacement overview

Which fuel injectors fit this Challenger?
The featured A-Premium six-piece injector set, ASIN B0CKVYT5XM, is listed for selected 3.6L applications. The corresponding manufacturer catalog is APFI174, with interchange references including 0280158233, 5184085AD, 05184085AC and FJ1147. These are cross-reference numbers, not a claim that the aftermarket set is a genuine Bosch or Mopar product. [1]
“4 holes” describes the nozzle, not the quantity: this package contains six multi-port gasoline injectors. The listing describes two-blade electrical connections and preinstalled O-rings. Match the original injector identification, engine, connector and supplier’s VIN-specific fitment before purchase. Package photographs and a shared engine displacement alone are not enough.
Retailer: Amazon · Disclosure. Check the selected variation, seller, current price and package contents before ordering.
Manufacturer-listed vehicle applications
Every row below is limited to the listed 3.6L V6 application. This is a parts-catalog summary, not permission to use the Challenger removal procedure on a van, Jeep or front-wheel-drive car. Confirm the actual vehicle and part number with the supplier. [1]
| Vehicle | Listed years |
|---|---|
| Dodge Challenger | 2011–2017 |
| Dodge Charger | 2011–2019 |
| Dodge Avenger | 2011–2014 |
| Dodge Durango | 2011–2015 |
| Dodge Grand Caravan; Dodge Journey | 2011–2019 |
| Chrysler 200 | 2011–2017 |
| Chrysler 300 | 2011–2019 |
| Chrysler Town & Country | 2011–2016 |
| Jeep Grand Cherokee | 2011–2015 |
| Jeep Wrangler | 2012–2017 |
| Ram 1500 | 2013–2017 |
| Ram C/V | 2012–2015 |
| Ram ProMaster 1500 / 2500 / 3500 | 2014–2018 |
| Volkswagen Routan | 2011–2014 |
Do not extrapolate fitment: this listing is not confirmation for a 3.5L Challenger, a HEMI V8, every Volkswagen or every later 3.6L engine. A modified or engine-swapped vehicle needs identification of its installed fuel system. The guide does not establish compatibility for a 2018-or-newer Challenger.
Symptoms and codes: what to test first
| Finding | Useful next check |
|---|---|
| P0201–P0206: injector circuit | Use the matching cylinder’s wiring diagram to inspect the connector, harness, electrical supply and control circuit. A replacement injector cannot fix an open wire. |
| P0300 or P0301–P0306: misfire | Compare ignition, fueling and compression-related evidence. Worn plugs, coil problems or a mechanical fault can mimic an injector complaint. |
| P0171 / P0174: lean indication | Investigate unmetered air and fuel delivery rather than assuming all six injectors are restricted. |
| Wet fuel, strong persistent fuel odor or flooding | Stop starting or driving the vehicle. Identify the leak or overfueling fault before further operation. |
The code descriptions come from the 3.6L diagnostic index; the table is a troubleshooting starting point, not a substitute for its individual test charts. [2] Record stored and pending codes, freeze-frame data and whether the symptom occurs cold, hot, at idle or under load. Keep that record before clearing anything.
Have fuel pressure, injector command and injector operation checked with the correct adapters and test procedure. Do not use an internet “universal” resistance or pressure number, energize an injector directly from a battery, or spray gasoline into an improvised container. A basic code reader cannot perform every factory injector test. When circuit testing or fuel testing exceeds your equipment and experience, pay for diagnosis before buying the kit.
What issues can this part fix?
- A confirmed internal injector electrical failure, after external wiring and control faults have been excluded.
- A confirmed restricted injector causing unequal delivery, where replacement is the appropriate repair.
- A confirmed leaking injector, with the cause of contamination or related damage addressed as needed.
These are conditional repair outcomes—not a guarantee that installing the set will clear a code, increase power or restore fuel economy. The presence of six new injectors in a box does not prove that all six on the car have failed.
Tools and supplies to have ready
Check your existing equipment first. The following links identify specific tools, not a mandatory shopping bundle. Verify socket fit on the actual hardware and use a suitable drive adapter or matching-drive socket where necessary.
- TEKTON SKT15301 socket and ratchet set — 3/8-inch drive, 46 pieces, including metric 8–19 mm and SAE 5/16–3/4 inch sockets. Add any smaller socket, extension or bit required by your car’s clamps and fasteners; this is not a promise that one set covers every access point.
- TEKTON 24320 inch-pound torque wrench — 1/4-inch drive, 20–200 in-lb. Its range includes the 2014 reference rail and upper-intake settings below. Confirm that the selected retailer variation is the 24320 inch-pound model.
- ANCEL AD310 OBD-II reader — for retrieving engine codes, supported live data and freeze-frame information. This is not a bidirectional injector-actuation or injector-flow tester. Manufacturer operating overview.
- INNOVA 3320 digital multimeter — optional electrical diagnostic equipment. Use the correct circuit diagram and non-damaging test leads; do not measure resistance on an energized circuit or probe terminals in a way that spreads them.
- 3M 91252H1-DC-10 chemical-splash goggles — eye protection to use alongside gloves selected for gasoline exposure.
Replacement materials and workshop essentials
Have the correct new upper-intake seals, new injector O-rings, clean engine oil for the specified seal lubrication, and any required injector retainers or damaged connector parts ready before disassembly. Match seal kits by VIN and the actual manifold. The injector package does not establish that manifold seals or every required retaining part are included. Do not remove the lower intake merely because a larger gasket kit contains extra seals. [4] [5]
Also prepare labels, a small fastener tray, clean lint-free intake-port covers, suitable absorbent material, a gasoline-rated container where required, wheel chocks and a serviceable extinguisher suitable for flammable-liquid fires. Inspect the fuel quick-connector before starting; use the release method and any tool specified for that connector rather than prying it apart. Specialized fuel-pressure adapters and enhanced diagnostic equipment are conditional needs, not assumed contents of the linked tools.
DIY versus shop price
The following is a worked budgeting example in US dollars, not a live product price, a local quote or a published labor allowance. Replace these assumptions with your actual parts offer and a written shop estimate.
| Illustrative assumption | DIY | Shop |
|---|---|---|
| Injector set: assume $100 | $100 | $100 before any markup |
| Seals and consumables: assume $50 | $50 | $50 |
| Labor: assume 3 hours at $150/hour | Your time | $450 |
| Example subtotal | $150 | $600 |
Diagnosis, tools, taxes, shipping, towing, shop markup and additional repairs are excluded. Ask whether the quote includes fresh seals, the correct injector calibration, fuel-leak inspection and verification of the original complaint. A broken connector or damaged manifold changes the scope; do not compare a bare parts price with a fully diagnosed shop repair.
Detailed repair instructions: 2014 Challenger SXT 3.6L
Before opening the fuel system: work on a cool engine with good ventilation, away from smoking, heaters, flames and sparks. Secure the vehicle on level ground. Wear splash protection and suitable gloves. Fuel pressure can remain with the engine off; follow the exact pressure-release procedure before disconnecting anything. Do not start a vehicle with an active fuel leak. [3]
Have the exact-year upper-intake removal instructions, fuel-connector procedure, injector/retainer diagram and tightening-sequence illustrations at hand. This overview uses the 2014 SXT service layout and does not replace those diagrams.
Removal and installation: 2014 Challenger SXT 3.6L
The steps below apply to the documented 2014 configuration. The broader parts-compatibility list does not extend these specifications automatically to other years. Have new injector O-rings, six upper-intake seals, a suitable inch-pound torque wrench and the matching fuel-line release tool ready. The linked numbered factory illustrations identify bolt positions; they are part of this procedure, not optional tightening guesses.
- Release pressure before disconnecting the battery. With no active fuel leak, identify the fuel-pump relay from the PDC cover label and remove it. Run the engine until it stalls, then try restarting until it will no longer run. Switch the ignition off and reinstall the relay. Disconnect and isolate battery negative. This is the 2014 pressure-release method; a leaking or already-disabled engine needs controlled pressure release by a technician, not repeated cranking.
- Remove the inlet assembly. Lift the engine cover from its ball studs. Unplug the intake-air-temperature sensor, loosen the clamps at both ends of the inlet hose, lift its retaining grommet from the stud and remove the hose.
- Free the upper intake. Unclip the brake-booster hose retainer. Unplug MAP and electronic-throttle connectors; release the throttle-harness clip and MAP-area harness retainer. Label and disconnect the PCV, brake-booster and EVAP purge hoses.
- Move the brackets—not the cooling hoses. Release the bracket harness retainer. Remove the first support bracket’s two nuts and loosen its stud. Remove the heater-return-tube upper support nut and move the tube aside without opening it. Remove the other two bracket nuts and loosen their stud retainers. The upper-intake removal illustrations distinguish these brackets.
- Lift the upper intake. Loosen its seven captive bolts and hold them clear while lifting. Do not confuse the nearby rail bolts with intake bolts. Discard the six intake seals, cover the open ports and lift off the left-cover insulator.
- Disconnect the fuel feed correctly. Place absorbent material below the closed joint before releasing it. Identify the latch style. On the redundant-latch/button type, pull the secondary latch outward, then press—not pry up—the button and withdraw the fitting. On latch-clip type 2, release and move the external clip, insert the correctly sized disconnect tool to free the internal latches, and withdraw with the tool inserted. Do not force a different connector with either method.
- Lift the rail. Release all six injector electrical plugs by their locks, not their wires. Remove the four rail bolts, then lift the rail evenly, containing residual fuel and checking for injectors or seals left in the manifold. Keep the connecting tube straight. Leave the lower intake installed for this rail service. [3]
- Install injectors and fresh seals. With the rail supported on a clean surface, withdraw the injectors without levering against terminals. Account for the old upper and lower O-rings. Clean the sealing bores; lightly coat correct new rings with clean engine oil. Fit the rings without twisting, then insert the injectors into the rail in their original electrical orientation. Do not add a retaining clip from a different engine’s instructions. 2014 injector installation.
- Seat and tighten the rail. Align all six injector tips with clean manifold bores and seat the assembly evenly by hand. Start all four bolts; use the numbered GC0144261 illustration in reference [4] and tighten to 7 N·m / 62 in-lb. Bolts must not be used to pull a cocked injector into its bore.
- Lock the fuel and electrical connections. Inspect the fuel fitting, clean it with a lint-free cloth and lightly lubricate its connection with clean engine oil. Push fully onto the tube until it clicks, restore its secondary latch/clip and pull firmly to verify retention. A clip that will not seat signals an incomplete connection. Reconnect the six injector plugs. Connector installation reference.
- Install the upper intake. Refit the insulator to its two posts. Remove every port cover, fit six new intake seals and keep injector wiring clear. Hold the captive bolts up while engaging the manifold’s locating posts. Tighten the seven bolts to 10 N·m / 89 in-lb in the numbered GC0144185 sequence in reference [5].
- Restore the supports and air path. Tighten support-bracket nuts to 10 N·m, their stud retainers to 20 N·m, and the heater-return support nut to 12 N·m. Reconnect PCV, booster and purge hoses, MAP/ETC plugs and harness clips. Seat the inlet hose and its grommet, tighten both clamps to 5 N·m and reconnect IAT. Refit the cover; reconnect battery negative at 5 N·m. [5]
- Check the closed system before normal driving. Clear fuel-wet materials and tools. With ignition on and engine off, use an appropriately capable scan tool’s ASD Fuel System test to run the pump; this is a pump test, not an injector-actuation command. Inspect the feed coupling and accessible rail joints without touching suspected leaks. Switch off immediately for wetness. The function is identified in the 2014 fuel-system diagnostic procedure. Do not assume a basic code reader can perform it.
- Run and recheck. After a dry static inspection, start with good ventilation and inspect again for leaks, abnormal idle and disconnected-hose symptoms. Stop for fuel odor, wetness or severe misfire. Record and clear only understood repair-generated codes, compare the original complaint and recheck pending faults after a safe road test. A cleared warning light alone is not proof of repair.
2014 Challenger SXT 3.6L reference specifications
| Fastener | Published 2014 reference value |
|---|---|
| Four fuel-rail bolts | 7 N·m / 62 in-lb, in the specified sequence. [4] |
| Seven upper-intake bolts | 10 N·m / 89 in-lb, in the specified sequence. [5] |
| Air-inlet hose clamps | 5 N·m / 44 in-lb. [4] |
These are inch-pound values, not foot-pounds. Brackets and other fasteners have their own specifications; do not apply the rail or manifold value to everything. Verify the exact year, manifold and service revision before using any number. Lower-intake removal, damaged fuel-line repair and wiring repair are separate operations requiring additional instructions.
Video: Pentastar injector diagnosis
This ProMasters Only video discusses testing Pentastar injectors and P0201–P0206 circuit complaints. It is a diagnostic visual reference, not an exact Challenger disassembly or torque guide. Use the vehicle-specific service information for the actual repair.
Frequently asked questions
Does P0203 mean injector number three is definitely bad?
No. It identifies the injector-three circuit. Inspect and test the circuit using the correct cylinder identification and wiring diagram before condemning the injector or control module.
Do I have to replace all six?
Not solely because the kit contains six. Diagnosis, contamination and the condition of the remaining injectors determine the repair scope. Use matched, application-correct parts when replacing more than one.
Does the set fit every 3.6L Chrysler or Jeep?
No such blanket fit is established here. Check the model, year, installed engine and original injector number. A compatible injector does not make access steps or tightening values interchangeable between vehicles.
Can I reuse the intake seals or old injector O-rings?
The cited 2014 instructions call for new injector O-rings and new upper-intake seals. Have them ready and follow the exact-year procedure. Preinstalled injector O-rings do not replace the separate intake seals.
What if it still misfires after replacement?
Stop for any leak or severe running problem. Recheck disconnected hoses, connector locks, wiring routing and intake sealing, then return to the original diagnostic evidence. An ignition, fuel-supply or mechanical problem can remain even after a faulty injector is repaired.
Service references and fitment sources
[1] Product and fitment: A-Premium APFI174 six-piece manufacturer catalog and the exact B0CKVYT5XM listing. Confirm the supplier’s current VIN-specific application before purchase.
[2] Fault-code definitions: 2014 Challenger SXT 3.6L diagnostic code index, original service information reproduced by LEMON Manuals.
[3] Rail removal and residual-fuel precautions: 2014 Challenger SXT 3.6L fuel-rail removal, Chrysler service material reproduced by LEMON Manuals.
[4] Injector seals and rail installation: 2014 Challenger SXT 3.6L fuel-rail installation, including the tightening-sequence illustration.
[5] Intake seals and reassembly: 2014 Challenger SXT upper-intake installation, including separate manifold, bracket and hose-connection requirements. Obtain the complete factory instructions for your exact vehicle.
Discuss your Challenger repair
Share the year, engine, symptoms, codes and test results in the Dodge Challenger chatroom. Do not post a full VIN publicly. Browse the fuel-pump and injector repair guides for related diagnosis and repair planning.
Share
2011–2017 Dodge Challenger 3.6L Fuel Injector Replacement — HowToMechanic
Link and QR card
For your shop, classroom, club, or car meet. Share only where invitations are welcome.